Mercedes Benz Repair Santa Rosa

Posted in Body Collision Repair Texas on June 28, 2019
Tags: , , , , , , , , , , , , , , , ,

Car repair service is something that it's worth spending some time doing a little research about in order to find a shop that's a good fit for you and your car. As with most services, it pays in the long run to spend some time shopping around for a good, honest car repair shop. Time spent finding the best South Texas auto repair facility for you and your car is an investment of time and effort that will give you peace of mind and could potentially lengthen the life of your car. Santa Rosa

Paint And Body Shops Near Me

When weather or bad luck leaves your car in need of professional body repair, car painting, or auto glass replacement, a qualified body shop or car rebuilder will give you straight answers, an honest estimate, and a clear timeframe.

Santa Rosa

Cheap Auto Paint Vehicle History OverviewThey don't make them like they used to.The First Cars The first motor cars were nothing more than a buggy and engine (Generally repaired by blacksmiths and carpenters. These cars were very expensive, which only the wealthy could afford) Model T was the first car mass production on an assembly line in 1908 (Ford's Vision was to produce an affordable car the average person could purchase) Model T's came in black only to keep the costs down. (The price came down once the assembly line was streamlined, but in 1908, the cost for a Model T started at $825. By 1913 the cost of the car reduced to $550)Cars in the 1960sCars were made the same basic way up through the 60s Body Over Frame Rear Wheel Drive (Same concept, but the cars were very big, bulky, and heavy) Except people in the 60s wanted SPEED! They achieved this with Big Block Motors, which created a lot of Horsepower. (The Birth of Hotrods, Rat Fink, Flames, and Pin Striping).Cars in the 1970s The government place strict fuel economy and emissions control laws Customers demanded cars with increased fuel economy New laws and customer demands started the automotive explosion of engineering ideas and changes in the automotive industry Changes to comply with Demands and LawsSmaller bodied cars and smaller engines Aerodynamics (Increase Fuel Mileage) Lighter cars by using different materials and designs More work-hardened areas created during formation of panel (Body Lines) SafetyConstruction of Interstate Highways + Higher Speed Limits + More High Performance Cars = Accidents and MoreDeaths from Auto AccidentsFederal Laws were passed to regulate safety. These laws included: Installation of seatbelts Safety glass windshields Head restraints In 1979, the first driver side airbag was introduced Airbags are mandatory in motor cars produced after 1990 Unibody Torque Boxes: Allow controlled twisting and crushing Crush Zones: Made to collapse during collision (To act as an absorber, absorbing the impact)Modern Day CarsCarbon Fiber Parts Aluminum Parts More Plastic Parts High Strength Steel Boron Steel Unibody Construction Space Frame Construction Computer Hybrid CarsNow they even have cars that will tell you when you're lost, where to turn, Parallel Park for you.ConclusionWhile the modern day cars appear to be made cheap and unsafe, they are actually designed to crush or collapse, while transferring the energy around the stronger passenger compartment to protect the passengers from injury.There is considerably more damage to modern day cars during a collision than the older vehicles, which gives the perception that "they don't make them like they used to". However, in reality the cars are taking the impact instead of the passengers.The lesson was designed to give you a little history, but to also emphasize that just a hammer, dolly and a few wrenches are not going to repair today's cars. We need highly trained collision repair and automotive technicians to repair today's vehicles.

Insist on Proper Auto Body Parts

Certified Collision Repair Center Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.Bumper RepairsWhen a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.Working with PlasticsThe first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.Adhesive RepairsThe bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.FlexibilitySome repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.Cleaning and PrepProper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible. Cheap Auto Paint

Body Collision Repair Texas

Comments are closed.