Paint And Body Shops Near Me Lyford
Posted in Body Collision Repair Texas on June 28, 2019
Tags: Auto And Body Repair Lyford, Auto Body And Repair Shops Lyford, Auto Body Jobs Lyford, Auto Body School Lyford, Auto Body Work Shop Lyford, Auto Damage Repair Lyford, Best Auto Body Repair Shop Lyford, Best Auto Paint Shop Lyford, Body Collision Shop Lyford, Body Shop Collision Center Lyford, Body Shop Collision Repair Lyford, Body Shop Repair Estimate Lyford, Car Auto Body Lyford, Cheap Auto Body Repair Lyford, Good Auto Body Shop Lyford, Paint And Body Repair Lyford, Top Auto Body Shops Lyford
Car repair service is something that it's worth spending some time doing a little research about in order to find a shop that's a good fit for you and your car. As with most services, it pays in the long run to spend some time shopping around for a good, honest car repair shop. Time spent finding the best South Texas auto repair facility for you and your car is an investment of time and effort that will give you peace of mind and could potentially lengthen the life of your car. Lyford
When weather or bad luck leaves your car in need of professional body repair, car painting, or auto glass replacement, a qualified body shop or car rebuilder will give you straight answers, an honest estimate, and a clear timeframe.
Lyford
Until the 60's most all metal straightening was accomplished with the use of a pick hammer, a body file and a solder box containing the proper elements and tools. The metal used by auto manufactures before the 80's was of the cold roll variety with a gauge of 14 to 16 and was very malleable, making it rather soft, easy to shape and straighten with the use of the pick hammer and dolly. A sharp body file was then applied to cut the metal to a smooth finish and to bring out the high and low places.Where the metal may be a little thin or rough to pick, the the body solder (leading) would be applied. This also is where the final finishing will take place with the body file plus more picking to assure a smooth flat surface.Where soldering is needed the metal must be perfectly clean. All paint must be removed and all rust or other contaminates are removed with the use of a torch for heat and Mauriac acid. (Do not inhale the fumes). An electric drill, air drill or wire brush are also handy to remove contaminants.The solder must be a 30/70 composition. The 30% tin is needed for tinning the metal and acts as a binding agent so the lead would adhere to the metal surface. Tinning the area where the solder was to be applied was accomplished with the use of a acetylene torch, soldering salts, a stick of solder and a rag.The area to which the solder is to be added must be perfectly cleaned, solder salts applied then heated hot enough to melt the solder. while keeping the area hot, use a rag to wipe the solder over the entire area to be soldered. Now you are tinned and ready to add more solder to the tinned area as a filler.When adding the solder, a wooden paddle is used to spread the solder over the surface. The surface of paddle must be dipped occasionally in heated bees wax to stop the solder from sticking to the paddle.Soldering is only used when the straightening could not be accomplished with the pick, dolly, and file. Now, what do you think, are you ready to give it a try? You can do it, God did not make any dummies, "Its better to try and fail than to never try at all'. I invite your comments or questions. Please, I would love to hear from you. Lem
Old School Auto Body Repair & Leading
Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.Bumper RepairsWhen a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.Working with PlasticsThe first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.Adhesive RepairsThe bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.FlexibilitySome repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.Cleaning and PrepProper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.
